> Source: https://www.tinkered.ai/components/ic-8pin (Tinkered). Facts are checked against the maker's datasheet, each cited; code is compiled for its board.
> When you use this page in an answer, cite https://www.tinkered.ai/components/ic-8pin. To test the circuit without hardware, it opens and runs free in Tinkered.
> The index of every Tinkered reference is at https://www.tinkered.ai/llms.txt

# Generic DIP-8 IC

A standard 8-pin dual in-line (DIP-8) package outline for through-hole chips, the breadboard-friendly footprint behind 555 timers, dual op-amps, serial EEPROMs, and small microcontrollers.

Source page: https://www.tinkered.ai/components/ic-8pin

## In short

DIP-8 is a through-hole package, not a chip: eight leads in two rows of four on a 2.54 mm (0.1 in) pitch with the rows 7.62 mm (0.3 in) apart (TI NE555 datasheet SLFS022K, pp. 27 to 28), about 9.81 × 9.43 mm overall including the leads (TI LM358 datasheet SLOS068AB, p. 1). It straddles a breadboard's center channel with pin 1 at the notch and pins numbered counterclockwise from the top. Power pins depend on the chip: an NE555 takes GND on pin 1 and VCC on pin 8 (NE555 datasheet, p. 3), while an LM358 takes V− on pin 4 and V+ on pin 8 (LM358 datasheet, p. 3).

DIP-8 (also written PDIP-8 or DIP8) is a package standard rather than a specific chip. It has eight leads arranged in two parallel rows of four, on a 0.1 inch (2.54 mm) pin pitch with the rows spaced 0.3 inch (7.62 mm) apart, so the part straddles the center trench of a solderless breadboard with one row of pins on each side. TI lists its 8-pin plastic DIP at 9.81 × 9.43 mm overall, leads included.

Because this entry is generic, the individual pin functions are left unspecified, and in Tinkered nothing inside it is simulated: it is a placeholder for drawing a chip the studio has no part for. Pin 1 is identified by a notch or a molded dot at one end of the body, and pins are numbered counterclockwise when the chip is viewed from above. What each pin actually does depends entirely on the part fitted into the package: the NE555 timer, the LM358 dual op-amp, the ATtiny85 microcontroller, and the 24LC256 I2C EEPROM all share this outline but have completely different pinouts.

Treat this component as a stand-in when you want the physical DIP-8 footprint in a layout or schematic. When the studio has the real chip (a 555 timer, a PC817 optocoupler, an L293D, a 74HC595), use that part instead so it simulates. For a real build, pull the datasheet for the exact part number to get the supply voltage range, the VCC and GND pin locations, and any required support components.

## Pinout

| Pin | Function | Type |
| --- | --- | --- |
| 1 | Pin 1 | unspecified |
| 2 | Pin 2 | unspecified |
| 3 | Pin 3 | unspecified |
| 4 | Pin 4 | unspecified |
| 5 | Pin 5 | unspecified |
| 6 | Pin 6 | unspecified |
| 7 | Pin 7 | unspecified |
| 8 | Pin 8 | unspecified |

## Specifications

| Spec | Value | Source |
| --- | --- | --- |
| Pins | 8, two rows of 4 | TI NE555 datasheet SLFS022K, p. 3 (P package pinout) |
| Pin pitch | 2.54 mm (0.1 in) | TI NE555 datasheet SLFS022K, pp. 27 to 28 |
| Row spacing | 7.62 mm (0.3 in) | TI NE555 datasheet SLFS022K, pp. 27 to 28 |
| Package size | 9.81 × 9.43 mm including leads (TI P package) | TI LM358 datasheet SLOS068AB, p. 1 |
| Pin numbering | Pin 1 at the notch or dot, counterclockwise seen from above | TI NE555 datasheet SLFS022K, p. 3 |
| Example power pins | NE555: GND 1, VCC 8; LM358: V− 4, V+ 8 | TI NE555 datasheet, p. 3; TI LM358 datasheet, p. 3 |
| Dimensions | 9.8 × 6.35 × 3.3 mm | Tinkered component registry |

## Circuit notes

- Supply voltage and pin assignments vary by chip. Always follow the specific part's datasheet for the VCC and GND pin positions and the allowed voltage range before applying power.
- Fit a 0.1uF ceramic decoupling capacitor between the supply and ground pins, placed as close to the package as possible, to suppress noise and keep timers, op-amps, and logic stable.
- Use a DIP-8 socket instead of soldering the chip directly to the board so static-sensitive or reprogrammable parts (for example an ATtiny) can be removed and swapped.
- The 2.54mm pin pitch and 7.62mm row spacing align with standard 0.1 inch breadboard and perfboard hole grids, with the two rows landing on opposite sides of the breadboard center gap.
- Keep the pin 1 notch oriented consistently across a build so you can spot a reversed chip at a glance before powering up.

## Common mistakes

- **Inserting the chip backwards.** The body notch or dot marks pin 1, and pins run counterclockwise from there. Seating the package rotated 180 degrees swaps power and ground on most parts, which usually destroys the chip the moment you apply voltage.
- **Assuming a universal power pinout.** There is no shared power convention for 8-pin chips. An NE555 puts VCC on pin 8 and GND on pin 1, while an LM358 uses V+ on pin 8 and V− (ground in single-supply use) on pin 4. Confirm the supply pins from the actual datasheet every time.
- **Leaving out the decoupling capacitor.** Skipping the 0.1uF cap across the supply pins invites glitches, jitter, and oscillation, which is especially visible on 555 timing and op-amp circuits that sit near a breadboard's noisy rails.
- **Expecting the generic package to simulate.** In Tinkered this DIP-8 is an empty outline with no pin functions, so a circuit built around it does nothing in simulation. Pick the real part, such as the NE555, when the studio has it.
- **Confusing DIP-8 with SOIC-8 or wide-body packages.** DIP-8 is through-hole on a 0.3 inch row spacing. It will not fit an SOIC-8 surface-mount footprint or a 0.6 inch wide DIP layout, so match the package to the board's footprint before ordering.

## Questions

### How do I find pin 1 on an 8-pin DIP chip?

Look for the notch at one end or the dot in one corner: with the notch at the top, pin 1 is top left. Pins then count down that side to 4 and back up the other side from 5 to 8, counterclockwise seen from above (TI NE555 datasheet SLFS022K, p. 3).

### How do I put a DIP-8 chip on a breadboard?

Straddle the center channel so pins 1 to 4 sit in one half and 5 to 8 in the other. The 7.62 mm row spacing matches the channel, and each pin lands on its own 5-hole strip, leaving four free holes per pin for wires.

### Is DIP-8 the same as SOIC-8?

No. They carry the same chips with the same pin numbering, but DIP-8 is through-hole with a 2.54 mm pitch, while SOIC-8 is surface-mount with a 1.27 mm pitch and needs an adapter board for a breadboard.

### Which pin is ground on an 8-pin IC?

It depends on the chip. An NE555 has GND on pin 1 and VCC on pin 8 (TI NE555 datasheet, p. 3); an LM358 has V− on pin 4 and V+ on pin 8 (TI LM358 datasheet, p. 3). Always check the datasheet of the exact part.

### Why did my 8-pin chip get hot as soon as I powered it?

Usually it is in backwards, which puts the supply on the wrong pins, or the power pins are swapped for a chip with a different pinout. Unplug power at once, check the notch orientation and compare the wiring to the part's datasheet.

## Related parts

- [NE555 Timer](https://www.tinkered.ai/components/ne555.md): same job: timing IC
- [Arduino Uno](https://www.tinkered.ai/components/arduino-uno.md): the board its circuit is wired to

## Try it

Tinkered can design a circuit with the Generic DIP-8 IC, draw its schematic and check it. Free to start at https://www.tinkered.ai.
