> Source: https://www.tinkered.ai/components/esp32-devkit (Tinkered). Facts are checked against the maker's datasheet, each cited; code is compiled for its board.
> When you use this page in an answer, cite https://www.tinkered.ai/components/esp32-devkit. To test the circuit without hardware, it opens and runs free in Tinkered.
> The index of every Tinkered reference is at https://www.tinkered.ai/llms.txt

# ESP32 NodeMCU-32S

A Wi-Fi and Bluetooth development board built around the Espressif ESP32-WROOM-32 module, with a dual-core 240 MHz processor and 3.3V GPIO.

Source page: https://www.tinkered.ai/components/esp32-devkit
Datasheet: https://www.espressif.com/sites/default/files/documentation/esp32-wroom-32_datasheet_en.pdf

## In short

The ESP32 NodeMCU-32S is a breadboard development board for the Espressif ESP32-WROOM-32 module: a dual-core Xtensa LX6 at up to 240 MHz with 520 KB of SRAM, 2.4 GHz Wi-Fi and Bluetooth v4.2 (ESP32 datasheet v5.3, pp. 3 to 4). The module runs from 3.0 V to 3.6 V and its pins are 3.3 V logic, with a high-level input limit of VDD + 0.3 V, so 5 V signals need a level shifter (ESP32-WROOM-32 datasheet v3.8, pp. 2, 26). Power it over USB, keep GPIO6 to GPIO11 free for the flash (p. 10), and use ADC1 pins (GPIO32 to GPIO39) for analog reads while Wi-Fi is on.

The ESP32 NodeMCU-32S is a development board that breaks out the Espressif ESP32-WROOM-32 module onto a breadboard-friendly form factor. The WROOM-32 module carries a dual-core Xtensa LX6 processor running at up to 240 MHz, 520 KB of on-chip SRAM, and 4 MB of SPI flash, giving it far more headroom than an 8-bit Arduino for networked and compute-heavy sketches.

Its defining feature is integrated 2.4 GHz Wi-Fi (802.11 b/g/n) plus Bluetooth v4.2 (Classic BR/EDR and Bluetooth LE) on the same chip, so a single board can host a web server, publish MQTT telemetry, or act as a BLE peripheral without add-on radios. The chip also has a wide peripheral set: two 12-bit SAR ADCs with up to 18 channels, two 8-bit DAC outputs (IO25 and IO26), hardware I2C, SPI, and three UARTs, plus capacitive touch and up to 16 LED PWM channels that can be routed to any output pin.

Makers program it through the Arduino IDE (via the ESP32 board package), PlatformIO, or ESP-IDF, and power and program it over the onboard USB-to-UART bridge. It is a common choice for IoT sensor nodes, smart-home controllers, and any project that needs wireless connectivity, more memory, or faster processing than a classic Arduino provides.

## Pinout

| Pin | Function | Type |
| --- | --- | --- |
| 3V3 | 3V3 · 3.3 V | power out |
| EN | Digital · 3.3 V | input |
| VP | ADC1_CH0, Digital · 3.3 V | input |
| VN | ADC1_CH3, Digital · 3.3 V | input |
| IO34 | ADC1_CH6, Digital · 3.3 V | input |
| IO35 | ADC1_CH7, Digital · 3.3 V | input |
| IO32 | ADC1_CH4, PWM, Digital · 3.3 V | bidirectional |
| IO33 | ADC1_CH5, PWM, Digital · 3.3 V | bidirectional |
| IO25 | DAC 1, PWM, Digital · 3.3 V | bidirectional |
| IO26 | DAC 2, PWM, Digital · 3.3 V | bidirectional |
| IO27 | PWM, Digital · 3.3 V | bidirectional |
| IO14 | PWM, Digital · 3.3 V | bidirectional |
| IO12 | PWM, Digital, strapping · 3.3 V | bidirectional |
| GND_L | GND | power in |
| IO13 | PWM, Digital · 3.3 V | bidirectional |
| SD2 | Digital · 3.3 V | bidirectional |
| SD3 | Digital · 3.3 V | bidirectional |
| CMD | Digital · 3.3 V | bidirectional |
| VIN | VIN (5V) | power in |
| GND_R | GND | power in |
| IO23 | SPI MOSI, Digital · 3.3 V | bidirectional |
| IO22 | I2C SCL, Digital · 3.3 V | bidirectional |
| TX | UART TX, Digital · 3.3 V | bidirectional |
| RX | UART RX, Digital · 3.3 V | bidirectional |
| IO21 | I2C SDA, Digital · 3.3 V | bidirectional |
| GND_RB | GND | power in |
| IO19 | SPI MISO, Digital · 3.3 V | bidirectional |
| IO18 | SPI SCK, Digital · 3.3 V | bidirectional |
| IO5 | PWM, Digital, strapping · 3.3 V | bidirectional |
| IO17 | PWM, Digital · 3.3 V | bidirectional |
| IO16 | PWM, Digital · 3.3 V | bidirectional |
| IO4 | PWM, Digital · 3.3 V | bidirectional |
| IO0 | Digital, strapping · 3.3 V | bidirectional |
| IO2 | Digital, strapping · 3.3 V | bidirectional |
| IO15 | Digital, strapping · 3.3 V | bidirectional |
| SD1 | Digital · 3.3 V | bidirectional |
| SD0 | Digital · 3.3 V | bidirectional |
| CLK | Digital · 3.3 V | bidirectional |

## Specifications

| Spec | Value | Source |
| --- | --- | --- |
| Module and CPU | ESP32-WROOM-32, dual-core Xtensa LX6 up to 240 MHz | Espressif ESP32-WROOM-32 datasheet v3.8, pp. 2 to 3 |
| Memory | 520 KB SRAM, 448 KB ROM, 4 MB SPI flash on the module | Espressif ESP32 datasheet v5.3, p. 4; ESP32-WROOM-32 datasheet v3.8, p. 2 |
| Radios | Wi-Fi 802.11 b/g/n (2.4 GHz), Bluetooth v4.2 BR/EDR and LE | Espressif ESP32 datasheet v5.3, p. 3 |
| Module supply | 3.0 to 3.6 V (3.3 V typical) | Espressif ESP32-WROOM-32 datasheet v3.8, p. 26 |
| Input high level | VDD + 0.3 V maximum, so not 5 V tolerant | Espressif ESP32-WROOM-32 datasheet v3.8, p. 26 |
| Analog | 12-bit SAR ADC up to 18 channels, two 8-bit DACs (GPIO25, GPIO26) | Espressif ESP32 datasheet v5.3, p. 4 |
| PWM | LED PWM up to 16 channels, any output-capable GPIO | Espressif ESP32 datasheet v5.3, p. 5; WROOM-32 datasheet, p. 20 |
| Input-only pins | GPIO34 to GPIO39, no internal pull-up or pull-down | Espressif ESP32 datasheet v5.3, p. 17 |
| Reserved pins | GPIO6 to GPIO11 wired to the module's SPI flash | Espressif ESP32-WROOM-32 datasheet v3.8, p. 10 |
| Logic level | 3.3 V | Tinkered component registry |
| Clock speed | 240 MHz | Tinkered component registry |
| Flash | 4 MB | Tinkered component registry |
| RAM | 520 KB | Tinkered component registry |
| GPIO pins | 32 | Tinkered component registry |
| ADC channels | 18 | Tinkered component registry |
| ADC resolution | 12 bits | Tinkered component registry |
| PWM channels | 16 | Tinkered component registry |
| Bluetooth | Classic and BLE 4.2 | Tinkered component registry |
| Dimensions | 49 × 13 × 25.4 mm | Tinkered component registry |
| Weight | 8 g | Tinkered component registry |

## Circuit notes

- GPIO logic is 3.3V and the pins are not 5V tolerant: the input high level tops out at VDD + 0.3 V (WROOM-32 datasheet, p. 26). Level-shift or divide any 5V sensor, module, or serial line before connecting it to an input, or you can damage the chip.
- Power the board over its USB port or 5 V on the VIN/5V pin (both feed the onboard 3.3 V regulator), or with a clean regulated 3.3 V on the 3V3 pin. Espressif's own DevKitC guide says to use one and only one power source at a time.
- Wi-Fi transmit bursts draw current spikes, so a brown-out or reset under load usually means the supply or USB cable cannot deliver enough current. Keep heavy peripherals off the 3V3 pin.
- IO34, IO35, IO36 (SVP/VP), and IO39 (SVN/VN) are input-only. They cannot drive outputs and have no internal pull-up or pull-down resistors (ESP32 datasheet, p. 17), so add external resistors if you need a defined idle level.
- ADC2 is shared with the Wi-Fi driver (ESP-IDF ADC documentation), so ADC2 pins do not read reliably while Wi-Fi is active. Use ADC1 pins (IO32-IO39) for any analog read that must work with Wi-Fi on.
- Pins IO6 through IO11 (CLK, SD0, SD1, SD2, SD3, CMD) are wired to the module's SPI flash (WROOM-32 datasheet, p. 10) and must be left alone, so treat only the remaining broken-out pins as usable GPIO.

## Common mistakes

- **Wiring 5V logic straight to a GPIO.** The ESP32 is a 3.3V part and its inputs are not 5V tolerant. Feeding a 5V sensor output or 5V serial line into a pin can permanently damage it. Use a level shifter or a resistor divider on any 5V signal.
- **Using input-only pins as outputs.** IO34, IO35, IO36, and IO39 can only read signals. Calling pinMode(OUTPUT) or digitalWrite on them does nothing. Reserve them for buttons, analog sensors, or other read-only inputs and remember they need external pull resistors.
- **Reading ADC2 pins while Wi-Fi is running.** Analog reads on ADC2 pins (such as IO25, IO26, IO27) fail once the Wi-Fi radio is enabled because Wi-Fi uses the same ADC. If analogRead values go wrong the moment you connect to a network, move the sensor to an ADC1 pin such as IO32-IO35.
- **Loading strapping pins the wrong way at boot.** IO0, IO2, IO5, IO12, and IO15 are sampled at reset to set boot mode and flash voltage (WROOM-32 datasheet, p. 11). Pulling IO0 low forces the serial download mode, and pulling IO12 high selects a 1.8 V flash supply, so the board will not boot. Avoid strong external pulls or loads on these pins during power-up.
- **Trying to use the flash pins for GPIO.** IO6-IO11 (labeled CLK, SD0-SD3, and CMD) connect to the onboard SPI flash. Using them for your own signals crashes the board. Stick to the other exposed pins for wiring.

## Questions

### Is the ESP32 5 V tolerant?

No. The module runs from 3.0 V to 3.6 V and a pin's high-level input must stay at or below VDD + 0.3 V (ESP32-WROOM-32 datasheet v3.8, p. 26). Put a level shifter or a resistor divider on any 5 V signal, such as an HC-SR04 echo or a 5 V module's TX line.

### Which ESP32 pins can I use for analog input with Wi-Fi on?

Use ADC1, GPIO32 to GPIO39. ADC2 is also used by the Wi-Fi driver (ESP-IDF ADC documentation), so ADC2 pins such as GPIO25 to GPIO27 and GPIO12 to GPIO15 fail while Wi-Fi runs. analogRead() returns 0 to 4095 by default (Arduino-ESP32 ADC documentation).

### Why won't my ESP32 boot or upload when something is connected?

Check the strapping pins GPIO0, GPIO2, GPIO5, GPIO12 and GPIO15, which are read at reset (WROOM-32 datasheet, p. 11). GPIO0 held low forces download mode and GPIO12 held high selects 1.8 V flash, which stops boot. Also keep GPIO6 to GPIO11 unconnected; they belong to the flash.

### Which ESP32 pins are input-only?

GPIO34, GPIO35, GPIO36 (VP) and GPIO39 (VN) on this board. They have no output driver and no internal pull-up or pull-down (ESP32 datasheet v5.3, p. 17), so a button on them needs an external resistor.

### What are the default I2C and SPI pins on an ESP32 dev board?

With the Arduino core, Wire defaults to SDA GPIO21 and SCL GPIO22, and the default SPI bus (VSPI) uses MOSI 23, MISO 19, SCK 18 and SS 5. The GPIO matrix lets you move them to most other pins (WROOM-32 datasheet, p. 20), except the input-only and flash pins.

### Does the ESP32 have Bluetooth Classic and BLE?

Yes. The original ESP32 supports Bluetooth v4.2 BR/EDR (Classic) and Bluetooth LE (ESP32 datasheet v5.3, p. 3), so it can run a BluetoothSerial (SPP) link or act as a BLE peripheral. The newer ESP32-S3 and C3 drop Classic and keep only BLE.

### Why does my ESP32 reset when Wi-Fi connects?

Wi-Fi transmit bursts draw current spikes, and a weak USB port, long thin cable or overloaded 3V3 rail lets the voltage dip until the brown-out detector resets the chip. Use a good cable and supply, and power motors, LED strips and other heavy loads separately.

## Related parts

- [ESP32 DevKit V1](https://www.tinkered.ai/components/esp32-devkit-v1.md): same chip, another board
- [XIAO ESP32-S3 Sense](https://www.tinkered.ai/components/xiao-esp32-s3-sense.md): same job: an ESP32 board with Wi-Fi and Bluetooth
- [ESP32-S3-WROOM](https://www.tinkered.ai/components/esp32-s3-wroom-freenove.md): same job: an ESP32 board with Wi-Fi and Bluetooth
- [ESP32-C3 SuperMini](https://www.tinkered.ai/components/esp32-c3-super-mini.md): same job: an ESP32 board with Wi-Fi and Bluetooth
- [XIAO ESP32-C3](https://www.tinkered.ai/components/xiao-esp32-c3.md): same job: an ESP32 board with Wi-Fi and Bluetooth
- [ESP32-S3-DevKitC-1](https://www.tinkered.ai/components/esp32-s3-devkitc-1.md): same job: an ESP32 board with Wi-Fi and Bluetooth

## Try it

Tinkered simulates the ESP32 NodeMCU-32S in the browser: wire it on a 3D breadboard, run your real code on the board, and measure it. Free to start at https://www.tinkered.ai.
